行业标准规范英汉对照-加工工艺（二）

122 GB/T 14235.6-1993 熔模铸造模料 酸值测定方法 Testing method for acid number of pattern materials in investment casting
123 GB/T 14235.7-1993 熔模铸造模料 流动性测定方法 Testing method for fluidity of pattern materials in investment casting
124 GB/T 14235.8-1993 熔模铸造模料 粘度测定方法 Testing method for viscosity of pattern materials in investment casting
125 GB/T 14235.9-1993 熔模铸造模料 热稳定性测定方法 Testing method for thermal stability of pattern materials in investment casting
126 GB/T 14408-1993 一般工程与结构用低合金铸钢件 Low alloy steel castings for general engineering and structural purposes
127 GB/T 15055-1994 冲压件未注公差尺寸极限偏差 Permissible stamping varitions in dimensions without tolerance indication
128 GB/T 15056-1994 铸造表面粗糙度 评定方法 evaluation method on cast surface roughness
129 GB/T 15111-1994 点焊接头剪切拉伸疲劳试验方法 Test method for shear tensile fatigue of spot welded joints
130 GB/T 15114-1994 铝合金压铸件 Aluminium alloy die-castings
131 GB/T 15115-1994 压铸铝合金 Die casting aluminium alloys
132 GB/T 15116-1994 压铸铜合金 Die casting copper alloys
133 GB/T 15117-1994 铜合金压铸件 Copper alloy die castings
134 GB/T 15169-1994 钢熔化焊手焊工资格考核方法 Approval testing of manual welders--Fusion welding-steel
135 GB/T 15620-1995 镍及镍合金焊丝 Nickel and nickel alloy welding wires
136 GB 15735-1995 金属热处理生产过程安全卫生要求 Requirements for the safety and health in production process of metal heat treatment
137 GB/T 15747-1995 正面角焊缝接头拉伸试验方法 Method of tension test for front fillet welded joint
138 GB/T 15825.1-1995 金属薄板成形性能与试验方法 成形性能和指标 Sheet metal formability and test methods--Formability and indexes
139 GB/T 15825.2-1995 金属薄板成形性能与试验方法 通用试验规程 Sheet metal formability and test methods--General test rules
140 GB/T 15825.3-1995 金属薄板成形性能与试验方法 拉深与拉深载荷试验 Sheet metal formability and test methods--Drawing and drawing load test
141 GB/T 15825.4-1995 金属薄板成形性能和试验方法 扩孔试验 Sheet metal formability and test methods--Hole expanding test
142 GB/T 15825.5-1995 金属薄板成形性能与试验方法 弯曲试验 Sheet metal formability and test methods--Bending test
143 GB/T 15825.6-1995 金属薄板成形性能与试验方法 锥杯试验 Sheet metal formability and test methods--Conical cup test
144 GB/T 15825.7-1995 金属薄板成形性能与试验方法 凸耳试验 Sheet metal formability and test methods--Earing test
145 GB/T 15825.8-1995 金属薄板成形性能与试验方法 成形极限图(FLD)试验 Sheet metal formability and test methods--Forming limit diagram (FLD) test
146 GB/T 15826.1-1995 锤上钢质自由锻件机械加工余量与公差一般要求 Machining allowances and tolerances for steel open die forgings on hammer--General reguirement
147 GB/T 15826.2-1995 锤上钢质自由锻件机械加工余量与公差盘、柱类 Machining allowances and tolerances for steel open die forgings on hammer--Disks and columns
148 GB/T 15826.3-1995 锤上钢质自由锻件机械加工余量与公差 带孔圆盘类 Machining allowances and tolerances for steel open die forgings on hammer--Disk swith holes